Congratulations To Our Most Recently Certified Water Restoration Technicians

Congratulations To Our Most Recently Certified Water Restoration Technicians, Matt Drinkwalter  & Billy Apostal

We are very proud off all of our employees and are committed to providing them with the latest in education. We keep our team members certified and constantly learning.

The Water Damage Restoration Technician course is designed to teach restoration personnel that perform remediation work to give them a better concept of water damage, it’s effects and techniques for drying of structures. This course will give residential and commercial maintenance personnel the background to understand the procedures necessary to deal with water losses, sewer back-flows, and contamination such as mold.

There are two key questions your water damage restoration contractor must be able to answer. First, what is the category of water? Second, how much damage or destruction has the water caused? Answers to these questions enable the water damage restoration contractor to create a professional scope of work and action plan.

What are the categories of water?

According to the IICRC, there are several different levels and classes involved in liquid destruction. From the IICRC’s S-500 standards, there are three categories describing the type of liquid involved:

Category 1 Water (Clean Water)

Water that originated directly from a sanitary source and when exposed to it, either through the skin, inhaled or ingested, does not cause a great deal of harm to humans. Examples of Category 1 Water: broken water supply lines, melting ice or snow, falling rain water, and tub or sink overflows (no contaminates).

Category 2 Water (Gray Water)

Defined as water with bacteria present, but no solid waste, carrying microorganisms and nutrients for microorganisms. Category 2 water does have the potential to cause discomfort or sickness if consumed or exposed to humans. Examples of Category 2 water: discharge from dishwashers or washing machines, toilet bowl overflows (urine, no feces), seepage due to hydrostatic pressure, and sump pump failures.

Category 3 Water (Black Water)

Contains pathogenic agents and is grossly unsanitary which includes raw sewage and other contaminated water sources, such as flooding from sea water, ground surface water and rising water from rivers or streams. To learn more about Category 3, read our two part series which described some of the challenges we faced during the Calgary flood in 2013.

HOW MUCH DAMAGE OR DESTRUCTION HAS THE WATER CAUSED?

According to the IICRC there are four classes of destruction:

Class 1

The lowest and easiest to deal with, this has a slow evaporation rate. Only part of a room or area was affected, there is little or no wet carpet, and the moisture has only affected materials with a low permeance rate, such as plywood or concrete.

Class 2

With a fast evaporation rate, this level affects an entire room, carpeting, or cushioning, the wetness has wicked up the walls at least 12”, and there is moisture remaining in structural materials.

Class 3

This class has the fastest evaporation rate, and ceilings, walls, insulation, carpet and sub-floors are all saturated. The liquid may have come from overhead.

Class 4

This class is labeled as specialty drying situations, which means there has been enough liquid and time to saturate materials with very low permeance, such as hardwood, brick, or stone.

It is important to understand that when you experience water damage, the longer you wait to begin dealing with the concern, the worse it can get. You should not allow the water to sit because the risk of bio-hazard increases. In short, in 2 to 3 days, category 1 water can turn into category 2 water and eventually category 3 water as other bacteria and pathogens begin to proliferate.

Bottom line, act immediately. Call a restoration professional to assess the category of water and extent of damage. Once this is determined, the scope of work will assess structural issues based on the class of damage, outline what contents need to be removed, how to deal with and remove excess water, a drying and monitoring strategy using air movers and dehumidifers, and a sanitizing plan to ensure a healthy environment.

It is important to understand that the goal of water damage restoration is to restore the property to pre-loss condition. With this in mind, once all the work has been done we strongly advise that you hire a Third Party Environmental consultant to perform post-remediation tests, particularly, if any mold or category 2 or 3 water was present. This final step will provide further peace of mind that the water damage restoration contractor you hired did a professional job.

 

Mold Training Course in Saskatoon, Saskatchewan- April 23, 2016

A mold training course on how to recognize indoor mold, how to develop effective sampling strategies, how to interpret laboratory results and how to control mold growth is scheduled for April 23rd, 2016 in Saskatoon, Saskatchewan.

saskatoon-training-april-23The public awareness of health effects associated with indoor mold exposure has been increasing since information is now readily available. Mold has been recognized as one of the major triggers of asthma and other respiratory diseases in recent years. As such there is increased demand for professionals who can identify the causes of mold growth and advise property managers, landlords and homeowners on how to remove and control mold growth.

The mold training course is designed to help mold inspection professionals to understand important aspects of mold growth in buildings. The course addresses where mold can grow in buildings, health effects, testing methods and interpretation of lab results, mold guidelines and steps to take to prevent future mold growth. It is the most in-depth, comprehensive mold training course on the market today.

To register for mold training course, call got mold? at 1-306-652-6653! This mold training course focuses on how to recognize indoor mold, develop effective sampling strategies, interpret laboratory results and how to control mold growth.

You will learn about:

  • The Various Types of Molds
    • What is mold and what makes it grow?
    • Which molds are more prevalent in outdoor environment?
    • Which molds are more prevalent in indoor environment?
    • What health effects are associated with indoor mold growth?
  • How to Recognize Indoor Mold Growth
    • Factors favouring mold growth
    • Signs of mold growth
    • Conducting a visual inspection and categorizing the extent of the mold contamination
  • How to Develop Effective Sampling Strategies
    • Sampling objectives
    • When to collect samples, which ones and where to collect them
    • Air samples: viable and non-viable
    • Bulk samples
    • Swab samples
    • Tape lift samples
    • Dust samples
  • How to Interpret Laboratory Results
    • Air samples: viable and non-viable
    • Bulk samples
    • Swab samples
    • Tape lift samples
    • Dust samples
  • How to Control Mold Growth and Perform Effective Mold Remediation
    Various mold remediation guidelines are discussed with emphasis to Mold Guidelines for the Canadian Construction Industry (2004).
  • Quiz and Discussion
    • Participants are given the opportunity to share and learn from each others’ experiences

Who Should Attend?

  • Industrial hygienists
  • Environmental consultants
  • Home Inspectors
  • General contractors
  • Cleaning and restoration contractors
  • Property managers
  • Insurance, financial, and legal professionals who deal with mold issues
  • Other professionals or anyone interested in increasing their knowledge or developing their decision-making skills related to indoor mold

 

Logistics & Lunch

The course breaks for lunch from 12:00pm to 12:45pm. Lunch and coffee/drinks are provided.

Course Venue
Details of the course venue will be provided during registration.


Course Fee
Take advantage of our promotional course fee of $399.99 (plus GST/HST). Our regular fee is $455.00 plus GST/HST. To reserve a place, please call 1-306-652-6653 today. Payment can be made by credit card (Visa or MasterCard) or by cheque. Please make cheques payable to got Mold? Disaster Recovery Services Inc.

Course Directors

Dr. Jackson N. Kung’u (B.Sc., M.Sc., Ph.D)

Jackson is the Principal Microbiologist and founder of Mold & Bacteria Laboratories (MBL) Inc., based in Mississauga, Ontario. He has over 27 years of experience in mycology (the study of yeasts and molds). Dr. Kung’u graduated from the University of Kent at Canterbury, UK with a Masters degree in Fungal Technology and a Ph.D in Microbiology.

Over the last 15 years, Dr.Kung’u, has been directing an indoor mold training course that was recognized by the American Board of Industrial Hygiene (ABIH), the Canadian Registration Board of Occupational Hygienists (CRBOH), the Institute of Inspection, Cleaning and Restoration (IICRC), the National Association of Certified Home Inspectors (NACHI) and the Registered Insurance Brokers of Ontario (RIBO).

Dr. has personally analyzed thousands of samples for mold such as air, fluids and bulk samples collected from homes, schools, offices, hospitals, industrial, agricultural, and other environments.

James C Watson, Founder, President & CEO of got mold?

James has been to 1000’s of homes and businesses that have been flooded and or infested with mold and asbestos. Mr. Watson offers his advise and expertise to anyone who needs assistance with disaster related issues.

Cancellation Policy:

Substitutions (in writing) are welcome anytime, but please notify us as soon as possible.

Early cancellations (more than two weeks prior to the course date):
Refund of the registration fee paid, less a 25% processing charge.

Late cancellations (less than two weeks prior to the course date):
Refunds cannot be issued for late cancellations.

Course Cancelled: If, for any reason, got Mold? cancels the course, your entire registration fee will be refunded.

Please Note: To avoid inconvenience, and to ensure you will receive a copy of the relevant training documents for this course, please pre-register by phone no later than 48 hours before the program is due to start.

To register for the mold training course complete the registration form below or Call 1-306-652-6653!

Are you ready for the winter?

Are you ready for the winter?

Winter is just around the corner. With the first few snowflakes that landed this morning and melting as it hit the ground we start thinking about the last minute fixes and things we needed to get done before the winter hits. Are you and your home ready for the cold weather? Have you done any upgrades during the summer that will allow your home to hold in more heat? Upgraded from a chimney vented furnace to an energy efficient? These type of upgrades are great however, they may cause higher humidity and in turn condensation at any cold spots such as where the drywall meets the ceiling. Getting the exterior of the home ready for the cold winds, snow and ice is critical for keeping Old Man Winter out and keeping it warm and toasty inside.

Windows and Doors

  • Check and replace if necessary all the weatherstripping around windows and doorframes for leaks to prevent heat loss, condensation and frost build up.
  • Examine wooden window frames for signs of rot or decay. Repair or replace framing to maintain structural integrity. If you believe it is mold infested and has wicked into your walls contact a professional for a mold inspection – Thermal Imaging  may be necessary and the best time to detect heat loss in your home is when it is cold outside.
  • Check for drafts around windows and doors. Caulk inside and out, where necessary, to keep heat from escaping.
  • Inspect windows for cracks, broken glass, or gaps. Repair or replace, if needed.

 

Lawn, Garden, and Deck

  • Trim overgrown branches back from the house and electrical wires to prevent iced-over or wind-swept branches from causing property damage or a power problem. In some cases it could be the cities responsibility to do this and all you usually have to do is report it. .
  • Ensure rain or snow drains away from the house to avoid foundation problems. The dirt grade — around the exterior of your home — should slope away from the house. Add clay and or extra dirt to lower areas, as necessary.
  • Clean and dry patio furniture. Cover with a heavy tarp or store inside a shed or garage to protect it from water damage or rusting.
  • Clean soil from planters. Bring pots made of clay or other fragile materials indoors. Because terra cotta pots can swell and crack, lay them on their sides in a wood carton or better yet a plastic tote.
  • Remove any attached hoses and store them away for the winter to prevent cracks, preserve their shapes, and prolong their life. Wrap outside faucets with covers to prevent water damage.
  • Shut off exterior faucets. Drain water from outdoor pipes, valves, and sprinkler heads to protect against pipe bursts. Have your sprinklers professionally blown out.
  • Inspect decks for splintering, decay, or insect damage and treat, if needed, to prevent further deterioration over the winter.
  • Clean leaves, dirt, and pine needles between the boards of wooden decks to thwart mold and mildew growth.
  • Inspect outdoor lighting around the property. Good illumination will help minimize the chance of accidents on icy walkways at night.
  • Check handrails on exterior stairs to make sure they’re well secured.

 

Tools and Machinery

  • Bring all your seasonal tools inside and spray them with a coating of lightweight oil to prevent rust. Pam cooking oils work great for this.
  • Move your snow blower and shovels to the front of the garage or shed for easy access.
  • Prepare the snow blower for the first snowfall by changing the oil and replacing the spark plug.
  • Sharpen ice chopper and inspect snow shovels to make sure they’re ready for another season of work. There is nothing worse then finding out your shovel is broken when you need it most!
  • Make sure you have an ample supply of ice melt or sand on hand for steps, walkways, and the driveway. If you rent – make sure your landlord is okay with you using salt on your walkways and always make sure to keep the salt off the grass to keep the lawn nice and green in the spring.

 

Heating, Ventilating, and Air Conditioning

  • Inspect the firebox and flue system to ensure that they’re clean of any soot or creosote and that there aren’t any cracks or voids that could cause a fire hazard.
  • Clean or replace the air filter in your furnace for maximum efficiency and improved indoor air quality. The filter should be replaced every month for best efficiency.
  • Clean any humidifiers and replace the evaporator pad.
  • Bleed valves on any hot-water radiators to increase heating efficiency by releasing air that may be trapped inside.
  • Check that smoke alarms and carbon monoxide detectors are in working order. You should replace the batteries regularly just to be safe!
  • Install foam-insulating sheets behind outlets and switch plates on exterior walls to reduce outside airflow.
  • Flush a hot water heater tank to remove sediment, and check the pressure relief valve to make sure it’s in proper working order.
  • Examine exposed ducts in the attic, basement, and crawl spaces, and use a sealant such as spray foam to plug up any leaks.
  • Check and make sure the insulation in the attic is not being compromised by mice, bats or other rodents. This is a lot more common then you think!

 

Gutters, Roof, and Drains

  • Check for missing, damaged or warped shingles and replace, as necessary before you get stuck with a leak.
  • Check for deteriorated flashing at the chimney, walls, and skylights and around vent pipes. Seal joints where water could penetrate, using roofing cement and a caulking gun.
  • Rake up leaves and debris from the yard and pool storm drains to prevent blockages.
  • Check all vents and openings and make sure they are covered to prevent insects, birds, and rodents from getting inside to nest in a warm place.

 

For a mold inspection to ensure the air quality of your home is safe call us today! Peace of mind is just a phone call away! 1-888-909-6653 a friendly knowledgeable representative is always available for information and advise.

Mold and Mycotoxins: Often overlooked factors in Chronic Lyme Disease

“Lyme” Is More than Lyme Alone

Mold & mycotoxins can be linked to Lyme Disease

Mold & Mycotoxins – linked to Lyme Disease


In the recently released book “Why Can’t I Get Better?: Solving the Mystery of Lyme and Chronic Disease” by Richard I. Horowitz, MD, a compelling argument is made that there is much more to chronic Lyme disease than Lyme alone. In fact, Dr. Horowitz unveils his “16-Point Differential Diagnostic Map” which suggests numerous “nails” in the foot which must be explored in order to regain wellness. He further expands the concept of “chronic Lyme disease” by suggesting MSIDS, or Multiple Systemic Infectious Disease Syndrome, as a more encompassing term for the multiple underlying factors involved in chronic illness.

In my personal experience recovering from Lyme disease after a tick bite in 1996 in Northern California, the journey has been one of uncovering many stones and addressing numerous layers of issues that were impacting my health. While Borrelia, Bartonella, Babesia, Ehrlichia, and many other microbial factors did play a role, it was not until I read the book “Mold Warriors” by Ritchie Shoemaker MD in 2006 that I considered the possibility of mold as another key part of the systemic body burden that had unknowingly made me ill for so many years.

Upon further evaluation, it was determined that I had been living in an apartment for nearly ten years that was contaminated with numerous molds including Stachybotrys, better known as “toxic black mold”. Removing myself from this constant, daily exposure to an environment that was not conducive with my recovery was an important step to take. Moving to a safer environment was one of the best things that I did as part of my journey back to health. I do not think I would be where I am today if I had not discovered and addressed this ongoing, toxic environmental factor that was contributing to my then poor state of health.

The connection between those struggling with chronic Lyme disease and ongoing exposure to toxic molds and mycotoxins is quite clear. Dr. Wayne Anderson has found that exposure to Lyme disease can make one more susceptible to mold illness, and vice versa; exposure to mold can make one more susceptible to Lyme disease. Both have the potential to affect the immune system and make the other more difficult to treat.

Dr. Neil Nathan has found mold toxicity to be a big piece of the puzzle in a very significant portion of patients with chronic Lyme disease. Lisa Nagy MD has suggested that many Lyme patients have a damaged immune system resulting from mold or pesticide exposures and that a focus on Lyme and co-infections may not always be the right focus.

One of the downsides of “chronic Lyme disease” is that Lyme often becomes the focus of treatment when, in fact, it may not be the dominant stressor that the body is burdened by. The intent behind this article is to suggest a more expanded view of chronic Lyme disease and to consider that both environmental exposures to toxic molds and the production of mycotoxins resulting from fungal colonization in the body can be significant issues in terms of symptom presentation; as well as both the severity and duration of the illness.

What Are Molds and Mycotoxins?

Mold and yeast are both different types of fungi. Molds are multicellular fungi and grow in filamentous hyphae, or long thread-like branches. They produce airborne spores, and are often quite colorful. In nature, molds are the recyclers of organic waste. While they are closer to plants than animals, they cannot undergo photosynthesis and thus rely on organic matter for nutrition. They reproduce using both sexual and asexual methods. Yeasts are single-celled microscopic fungi that are round or oval in shape and are generally colorless in appearance.

They reproduce asexually via mitosis or budding. Yeasts are often used in fermentation of alcoholic beverages such as wine and beer and are used in baking. Some yeasts, such as Candida albicans, can be opportunistic infections in humans.

Mycotoxins are toxic chemicals produced by both molds and yeasts. They are believed to be used by fungal organisms as a protective mechanism; as a way to stake out their territory and to allow for further proliferation of the fungi. Additionally, within a host, they may be used by the fungi in order to weaken host defenses in support of persistence of the fungal organisms.

The environment in which the fungi live may be directly correlated to the output of mycotoxins. The more threatened the fungi are by the surrounding environment, the more they may utilize mycotoxin production as a protective weapon. Mycotoxins are not essential for the fungi to maintain their existence, but they do provide a competitive advantage. In some cases, humans get caught in the crossfire.

Mycotoxins in the body may be the result of external exposure to molds or internal, colonizing fungal organisms. They are generally found intracellularly and may be stored in body fat, myelin, tissues, organs, and other body sites.

While there are hundreds of different mycotoxins that have been discovered, some of the more common ones include aflatoxin, ochratoxin, citrinin, ergot alkaloids, patulin, fumonisin, trichothecene, and zearalenone. The focus of this article will be on aflatoxin, ochratoxin A, and trichothecene given that these can be readily measured via laboratory testing performed on a urine sample; providing a useful tool for practitioners working with patients with mold-associated illnesses.

Ongoing mold and mycotoxin exposure can be a very serious issue creating illness in the genetically susceptible. Sadly, the importance of evaluating for the potential of mold illness and taking appropriate corrective actions is often overlooked by many practitioners and patients alike.

Shoemaker’s Mold Contributions

Ritchie C. Shoemaker MD deserves tremendous credit for being the voice that brought mold illness to our awareness. His “Biotoxin Pathway” and treatment protocol have been instrumental pieces of the puzzle for many struggling with chronic biotoxin illness. Biotoxins are toxins created by living organisms. Mycotoxins are a subset of biotoxins and are produced by fungal organisms.

Visual Contrast Sensitivity (VCS) testing is often a very useful biotoxin screening tool that can be performed online. Mycometrics ERMI (Environmental Relative Moldiness Index) is arguably one of the best evaluation tools for the presence of mold in an indoor environment. Numerous lab tests were brought to our attention by Dr. Shoemaker’s work including HLA testing, which looks for genetic predispositions to various biotoxin illnesses, and markers such as TGF-β1, C4a, C3a, MSH, VIP, VEGF, MMP-9, and others. The information that a trained practitioner can ascertain from the results of these tests is significant in their work to guide a biotoxin-illness patient back to a higher level of health.

Cholestyramine is used in many with Lyme disease and mold illness as a direct result of Dr. Shoemaker’s discoveries. Losartan, VIP nasal spray, and other useful therapeutic options have been introduced to biotoxin-illness sufferers through his work.

Dr. Shoemaker’s approach has benefited and will continue to benefit many suffering with otherwise unexplained illnesses. No article on the topic of mold illness would be complete without a mention of his important contributions, and while not the focus of this article, his work has been life changing for many; myself included. More information about his protocol, his books (Mold Warriors; 2005, Surviving Mold; 2010), and the recently introduced doctor certification program can be found on his web site. Several integrative practitioners now incorporate a combination of the Shoemaker Protocol with several of the other options discussed in this article.

Mold and Mycotoxin Symptoms and Associated Conditions

Symptoms produced in humans as a result of mold and mycotoxin exposure are widely varied and may range from no response or simple allergy to cancer or even death.

“Symptoms can be caused by mold allergy, mold colonization (or infection), or mold toxicity, or a combination of these. Until Dr. Shoemaker raised awareness around the toxicity component, we had focused exclusively on allergy and infection. It is the understanding that mold toxicity, with its marked, uncontrolled outpouring of inflammatory cytokines, produces the same wide array of unusual symptoms that we see in Lyme disease and its co-infections that has dramatically improved our ability to diagnose and treat a large subset of patients that had been previously struggling to get better,” said Dr. Neil Nathan.

The symptoms may be dependent on the types of molds and mycotoxins, the duration of the exposure, and the overall health of the exposed person. Mycotoxins damage the immune system and may make one more sensitive to bacterial endotoxins found on the outer membrane of bacterial cell walls. With an increased sensitivity, the body’s response to Borrelia burgdorferi, the causative agent of Lyme disease, and co-infections may be heightened and lead to a further exacerbation of overall symptoms.

Mycotoxins can cause coughing, wheezing, asthma, shortness of breath, sneezing, burning in the throat and lungs, and sinusitis. Memory loss, confusion, brain fog, and cognitive impairment may present. Vision problems, eye irritation, headaches, swollen lymph nodes, ringing in the ears, dizziness, hearing loss, fatigue, muscle weakness, multiple chemical sensitivities, joint pain, muscle pain, irregular heartbeat, seizures, depression, anxiety, irritability, psoriasis, skin irritation, fever, chills, sleep disorders, coagulation abnormalities, and numerous other symptoms have all been associated with mycotoxin exposures.

According to Dr. Joseph Brewer at the 2013 ILADS annual meeting, mycotoxins bind to DNA and RNA, alter protein synthesis, increase oxidative stress, deplete antioxidants, alter cell membrane function, act as potent mitochondrial toxins, and alter apoptosis.

Molds and their mycotoxins may negatively impact the endocrine system including sex hormones, thyroid function, and adrenal function. Mold exposure may lead to food allergies and chemical sensitivity. In some cases, POTS (Postural Orthostatic Tachycardia Syndrome) may be mold-induced.

Fibromyalgia and Chronic Fatigue Syndrome have both been associated with mycotoxin exposure. Other conditions that may have a mycotoxin component may include various cancers, diabetes, atherosclerosis, cardiovascular disease, hypertension, autism, rheumatoid arthritis, hyperlipidemia (elevated cholesterol), inflammatory bowel disease, Lupus, Sjögren’s syndrome, Crohn’s disease, Multiple Sclerosis, Alzheimer’s disease, Raynaud’s Disease, kidney stones, vasculitis, and others.

It has been suggested that elevated cholesterol may be a protective mechanism of the body as a response to mycotoxin exposure. Statin drugs have antifungal properties, and one of the mechanisms through which they may help to lower cholesterol is through the reduction of mycotoxins as systemic fungal populations are reduced.

In those with chronic Lyme disease, it is difficult to separate the symptoms associated with mold and mycotoxin exposure from those associated with Lyme disease or even those associated with heavy metal toxicity. The overlap is significant, and as a result, all of these items must be explored as symptoms believed to be associated with Lyme disease may not be entirely the result of Lyme itself.

For more information check out BetterHealthGuy.com

Mans Best Friend Can Also Detect Mold

Mold Detection Certified Dogs can save the consumer thousands in pinpointing the location of the mold in a building.

Mold Detection Certified Dogs can save the consumer thousands in pinpointing the location of the mold in a building.

Dogs have been used for years by military and law enforcement agencies to detect bombs and drugs, among other things. In Europe, dogs have been used to detect mold for over 20 years.

Mold frequently grows in hidden places, inside wall cavities, underneath floors and in inaccessible areas and is often not visible until the problem is more advanced. When moisture builds up from leaky pipes, roofs, basements or high humidity, conditions are ideal for mould growth. Moulds are easily disturbed and their spores can become airborne causing a possible threat to the building or the health of the occupants. Exposure to some types of moulds can cause serious health effects such as respiratory infection, asthma attacks, skin rashes, eye infections, ear infections, nosebleeds and headaches. In rare cases toxic mould can cause cancer and even death.

Certified Mold Dogs detect and pinpoint exact areas of mold, which leads to lower remediation costs for homeowners and insurers.

A MOLD DOG can get to places faster than people, and can detect mold in places that people can’t reach. Human inspectors might be in a building for four hours performing Indoor Air Quality tests and sampling and even using thermal imaging cameras before finding the mold where as a mold dog can sniff it out and represents the newest tool for consumers in North America to detect and more importantly, pinpoint mold in structures, thus lowering remediation costs.

Top 5 Reasons to use a mold dog

1. Mold Dogs are a Proven Technology. In Europe, dogs have been used to detect mold for over 20 years.
2. A Mold Dog  is an Effective Problem Solver. Mold Dogs can quickly and more accurately inspect a home.
3. A Mold Dog’s Nose is a More Accurate Tool. The “Nose” is cutting-edge technology in the home inspection industry. It is the only inspection tool that can detect and pinpoint sources of mold.
4. A Dog Will Help You Manage Your Exposure to Mold. Quicker and more accurate detection of mold leads to lower remediation costs. For schools, hotels, commercial, and government buildings, savings can be quite substantial.
5. A Dog Provides Honest and Credible Results. Mold-detection dogs aren’t biased.